Houston Garage

Garage Door Repair Houston – Texas

Garage Door Repair Services

We have the skills, equipment, and industry knowledge needed to make reliable garage door repairs in Houston, TX. Our technicians encourage you to hire a professional for repair any time you have a problem to prevent injuries and further issues. The CMG team is ready to help 24/7. CMG offer repairs for many garage door parts, including springs, cables, rollers, tracks, panels, and hardware. Whether you need to replace garage doors, a damaged panel or fix garage door opener problems, CMG is the garage door repair company for you

Broken Garage Springs

Springs are one of the integral parts of the garage door operation. Garage door springs are typically held in high tension and can be dangerous if broken or if there is heavy wear and tear. One of our technicians will ensure your springs are in full working condition. If not, we will have them replaced right away

Garage Door Cables

Yes, our technicians are trained to fix cable problems right the first time. Broken cables are one of the first signs of a garage door problem and are just a symptom of an underlying problem. You will not be able to operate your door correctly until this issue is fixed. We will fix it and fix it right the first time.
Bent or Broken Rollers

Did you know that a noisy garage door is often a sign of either broken or bad rollers? If your garage is everything besides a silent whisper, give us a call .

Torsion Spring

Springs provide 92% of the lift needed to make a garage door move. Torsion springs have long life expectancies if you invest in good parts in the beginning. You will not find torsion springs at a home improvement store because these are the most dangerous part of the door. You will need to hire an expert to repair or replace these. Please do not try to make this repair on your own if you do not have proper training.

Garage Door Panels

Accidents happen, and occasionally one or more of your garage door panels is damaged. We can match and replace damaged panels and have your garage door looking new in no time.

 

Garage Door Tracks

Tracks may get misaligned after an unexpected incident, such as running into the garage door with the car. You may need a full replacement or our team might be able to fix the repair with a few adjustments. It depends on the situation. Contact us for assistance.
Full Inspections

The goal of an inspection is to find the underlying causes of garage door problems. We inspect your setup for a solution, not where we can put a Band-Aid. The best way to find out the condition of your garage door is to request a professional for inspection. We offer a 25-point inspection to make sure your door functions properly and is safe for your daily use. Call us now to find out how soon we can service your home.
Why Invest in Good Parts?

If you’re like the typical American, you open your garage door several times a day. It might be even more if you have youngsters running around the house who also like to play outside. Investing in good parts will prolong the life of your garage door. You should be able to expect your door to open any time you press the button.

Contact us today to schedule a service for garage door repair in Houston, TX We look forward to helping you!

Garage door replacement

Professional Garage Door Installation and Repair

Garage door repair can be tricky. If you live in Houston, you can count on CMG Garage Door Repair to install you replacement door professionally.

Step 1: Remove the Old Door

Use the manufacturers’ instructions to remove the old door. It mainly consists of carefully unlatching the door from the pulley system, then taking apart the panels of the door and unscrewing the tracks. Make sure to remove one panel at a time, or they could all fall in on you.

Step 2: Measure, Attach Hinges and Handles

Measure the various areas where the door will be installed: door-opening height and width, headroom (from top of opening to ceiling), and back room (length of garage). For the headroom, you should have about 10″ to 12″ of space, depending on the spring system you’re installing. For the back room, you should have the door height, plus another 18″ or more of space.

With the proper measurements in hand, temporarily attach stops to both sides of the opening and make sure they are flush with the inside edge of the door jamb. Using the sawhorses, lay out the bottom piece of the new door, and attach any weather stripping (if necessary). Additionally, attach any hinges and lift handles to the piece.
Step 3: Set the Bottom Piece Into Position

Insert the bottom piece into the door frame, and use a level to properly set the piece. Once the piece is in place, tap nails partway into each jamb. Slant or slightly bend the nails to secure them in place. Use the manufacturer’s instructions to assemble the vertical, curved and horizontal pieces of the track and set aside.

More information about garage door repair in Houston, Tx

Houston Garage Door Services

Choosing the Right Garage Door Repair Service In Houston Texas

Does your garage door need repair?

CMG can repair  garage doors including: traditional steel garage doors, aluminum garage doors, wood garage doors, carriage style garage doors, fiberglass garage doors, vinyl garage doors and insulated garage doors.

Garage doors contain many moving parts. These moving parts can become worn with time. When this happens, it is time you repair your garage door or replace your garage door with a new one. If you decide to repair your garage door, then you will require the services of a professional company to do the repairs rather than trying to repair it on your own. Modern doors require specialized tools and a skilled technician to identify and repair the faulty areas.

There are many advantages of choosing CMG “Garage Door Repair of Houston for repairs as they will ensure that the door is properly fixed, safe, and completed in a timely manner at an affordable price.

When it comes to cost, it is not always the company offering the lowest price that provides the highest quality and safest service. Neither does a higher price always ensure quality! Do your homework and read reviews. Ask for quotations and compare the prices versus the experience that company has.

So, if you are in need of garage door repair or garage door service, contact CMG Garage Doors or Houston, Texas

Repair of Arched Garage Door in Houston, TX

Garage Door Repair Guide

When your garage door is not working properly, it can cause major frustration and you will lose access to an incredibly important part of your home.

Our staff is expertly trained to diagnose and repair all major makes and models of both overhead and garage doors. We offer same day service and are available for all of your garage door repair needs 24 hours a day. Call now for a free estimate at (713) 462-4364!

The garage door is probably the largest moving part around the house and of course it gets used a lot, so it is very important to keep it properly maintained.

Let CMG Garage Door Repair of Houston, Texas tackle your next garage door repair job. We have years of experince in garage door repair and service. Our Service area includes Houston, Sugar Land, Katy, The Woodlands, Spring Texas, Spring Branch, Clear Lake, Pearland Texas and Kingwood. Call Today for a Free Estimate!

  • First, check all the moving components of the door mechanism to make sure none are bent or broken.
  • Check and lubricate the rails and axels and make sure the axels are tight and secure. Lubricate the hinges, springs and rollers with light household oil.
  • Using a soft cloth, wipe down the door with a household detergent diluted with water. You can apply car wax to the door to keep it free of dirt and moisture.
  • On most garage door systems you can adjust the sensitivity of the door operation. Consult your manual to find out how.
  • Keep wooden doors painted inside and out, and caulk any cracks or gaps.
  • Check the weather sealant at the bottom of the door. If it is cracked or broken, it must be replaced.
  • Rust is a major enemy for any garage door. Yearly maintenance can help keep it away.
Garage Door Repair/Replacement Houston, Texas

Garage Door Repair Steps

Let Our Trained Professionals Repair Your Garage Door

Garage door repair is very labor intensive and dealing with a high load spring can be dangerous. We perform hundreds of garage door repairs in Houston, Texas. We have years of experience and strive for excellence in each and every garage door repair job. Give us a call today!

Step to Garage Door Repair

Step 1: Take the Door Measurements

Before purchasing a new garage door, take some measurements. Measure the width of the door from the actual structural member, not the trim piece.

Next, measure for head room so there is enough room for the door to actually operate. Lower the door to make sure there are no pipes or framing members in the way.

 

Step 2: Lower the Door

Each door is different — some need to be taken out when they are in the up position and some when they are in the down position. If a door has tension springs on them, it should be taken down when it is in the up position. It is very important that there is no tension on the door when taking it apart.

Once the door is up and locked into place there is no tension on the spring and it is safe to release it.

Keep in mind that when the springs are released there is nothing to help with weight replacement. Garage doors weigh 150 pounds or more and if the door were not locked in place, there would need to be some way of holding it up until it can be lower manually. If no one is available to help, a clamp can be put on the track at the end of the door . When ready, release the clamp and take the weight of the door.

Remove the tension spring cables and then carefully put the door down

 

Step 3: Remove the Door Panels

Remove the pin of the top center brace and loosen the brace .

Remove the nuts from the bolts on the top panel . Remove the nuts at the top of the next panel down. The first panel should come right out.

Continue this procedure until all the panels have been removed.

 

Step 4: Disassemble the Operator

Remove the old door tracks and the laser sensor that keeps the door from closing when an object is beneath it.

Remove the brackets holding the track in place. Disconnect the track from the brackets that allow it to hang from the ceiling. Keep a firm grip on the rail or it will fall .

Remove the old operator by unfastening the brackets holding it in place and snip the wiring . Use a ladder to rest the motor on until someone is available to help pull the whole thing down.

 

Step 5: Prepare the Frame

Before beginning installation, check to make sure all of the new door’s hardware is accounted for.

Remove the header trim and the old 2″ x 4″s so the rough opening can be reframed. Use new 2″ x 4″s for this and attach them with 16-penny nails.

 

Step 6: Level the New Door

Set the bottom piece of the new garage door in place to make sure it conforms to the concrete floor. Check it with a level and add shims until it is level. Use a compass to make sure it is the right distance between the concrete and the bottom of the door on the highest side. Transcribe a line across the bottom to show where to cut.

Use a circular saw to trim off the bottom of the panel. Trim slowly and follow the line as close as possible so it will be a nice fit to the door.

 

Step 7: Install Weather Stripping

To finish the bottom panel, install weather stripping using galvanized roofing nails.

Note: Weather stripping will wear out over time and needs to be replaced.

 

Step 8: Attach the Corner Brackets and Build the Hinges

The corner brackets usually have an R and an L on them so they can easily be installed on the correct side. Bring them all the way down flush to the bottom of the door . The heart shaped areas are where the screws go.

Next, start building the hinges. The hinges are all numbered at the bottom . The first section will be ones all the way across. The one always goes at the bottom. The next section will have twos on the corners and a one in the middle, the next will have threes on the sides and a one in the middle, etc.

 

Step 9: Install Tracks and Rollers

Once the hinges for the bottom panel are in place, install rollers in each of the ones at the sides.

Set the track around the bottom two wheels. Brackets will actually fasten the track to the wall, but it is better to wait until the end so the doors can be as close as necessary. Attach the brackets (they have a little play in them).

The track is slightly flexible so it is easy to fit the rollers into it. Attach the track to the new 2″ x 4″ framing.

 

Step 10: Mark the Hinges

The middle hinges go 48″ in from the edges of the panel, and the last hinge goes 1-3/4″ from the edge, just like the first one. Use a carpenter’s square to mark them before installing the hinges.

 

Step 11: Attach the Panels

Put together the tension rod assembly. Follow the manufacturer’s instructions for assembly very closely, because the springs on them are very strong.

It is important to bring all the door hardware, tools, and panels into the garage at this point, because until the panels are attached to each other, you are pretty much stuck in the garage when the panels start stacking up.

The tongue of each panel fits over the groove of the panel below it as the rollers slide on the panels down the track.

 

Step 12: Fasten the Tracks

Once satisfied that the rollers won’t bind in the track, fasten it down with screws. Connect the horizontal track and vertical track. It is extremely important that the two align correctly or the door will be out of line and the wheel will bump. Tie in the horizontal track . Connect the tracks on the other side.

 

Step 13: Install the End Bearing

The end bearing is what the tension rod will slide through and spin. It is simple to install. Both plates go on the outside. A hex head goes in the bottom and a carriage bolt in the top.

 

Step 14: Fasten the Hinges

Before setting the last panel in the tracks, set the power unit on the actual frame and slide it in the ends. Hardened screws are used to attach the center bracket. They are a different type screw — they are tougher and will last a lot longer. Make sure the bracket is level (to the eye) when installed and leave the bracket a little loose so adjustments can be made. Fasten down all the hinges

 

Step 15: Install the Cable and Spring

To install the cable that will pull the door up, attach it to the bottom panel.

Thread the cable through the cable winder and wrap it around. Once the cable is wrapped, tighten down the set screws . If preferred, a professional can be hired to wind the spring.

 

Step 16: Install the Operator Support

Install the brackets to hold the new operator. Make absolutely certain they are securely in place. A couple more brackets hang down and support the actual motor of the operator .

Attach the bracket holding the spring in place to the header support block. Attach the rail of the operator to the bracket and mount the motor .

 

Step 17: Install the Trim and Paint

To install the trim, use a paint scraper to get rid of the old caulk. The vinyl trim is installed with finish nails. Paint the door.

Note: A job like this is very labor intensive. Allow enough time to install the door so that it is done safely.

Image of a Gable Garage Door being repaired in Houston Texas

Garage Door Maintenance Tips


Garage door maintenance is not on most people’s regular to do list. But there are a few simple things you should do every year or so to keep the door rolling along trouble-free.

  1. Give all rollers, hinges, roller tracks, hinges, and latches a good squirt with a penetrating solvent like WD-40 or a citrus-based solvent. Lubricate the pulleys on extension-spring openers and the bearings on torsion-spring openers. Wipe a little oil on the torsion spring if it is rusty and binds up.
  2. Wipe everything clean, then apply a light oil, such as 3-in-1 lubricant, to the same parts.
  3. If any rollers or hinges seem stuck, try to soak them in some kerosene. Use a small brush (an old toothbrush works great) to work the kerosene into the cracks. Remove any rust with steel wool. Wipe all parts clean, then apply lubricant.
  4. Garage door maintenance is often needed on the door opener. If your garage door opener is operated by a chain or drive screw, apply the same lubricant to the full length.
  5. Check any weatherstripping along the sides of the doors. Adjust if it is jamming against the sides, and replace if necessary.
  6. If your garage door is wood and it doesn’t have bottom weatherstripping, make sure it has been sealed or painted. Touch up as needed, and consider adding weatherstripping.

Make garage door maintenance an annual project (spring or fall are good times).

Houston Garage Door Service

Garage Door and Opener Manufacturer List

Finding Garage Door Repair in Houston, Texas can be tricky. CMG Garage Door’s trained service professionals are certified to perform garage door repairs and service from most major garage door manufactures.

Carriage House Garage Door Manufacturers

Manufacturers of carriage house garage doors Website
Amarr Garage Doors www.amarr.com
Clopay Building Products www.clopaydoor.com
Delden Garage Doors www.deldenmfg.com
Garaga www.garaga.com
Northwest Door www.northwestdoor.com
Overhead Door www.overheaddoor.com
Raynor www.raynor.com
Safe-Way www.safe-waydoor.com
Wayne Dalton www.wayne-dalton.com

Contemporary Garage Door Manufacturers

Manufacturers of contemporary garage doors Website
Amarr Garage Doors www.amarr.com
Clopay Building Products www.clopaydoor.com
Delden Garage Doors www.deldenmfg.com
Garaga www.garaga.com
Northwest Door www.northwestdoor.com
Overhead Door www.overheaddoor.com
Raynor www.raynor.com
Wayne Dalton www.wayne-dalton.com

Raised Panel Garage Door Manufacturers

Manufacturers of raised panel garage doors Website
Amarr Garage Doors www.amarr.com
Clopay Building Products www.clopaydoor.com
Delden Garage Doors www.deldenmfg.com
Garaga www.garaga.com
Northwest Door www.northwestdoor.com
Overhead Door www.overheaddoor.com
Raynor www.raynor.com
Safe-Way www.safe-waydoor.com
Wayne Dalton www.wayne-dalton.com

Garage Door Opener and Accessories Manufacturers

Manufacturers of garage door openers Website
LiftMaster www.liftmaster.com
Overhead Door www.overheaddoor.com
Sommer USA www.sommer-usa.com
Garage door being repaired

Garage Door Care

Checking your rollers. Oil the torsion spring and hinges. These are basic periodic maintenance tips. It’s a good idea to test the operator. Make sure its sensors will stop the door should something get in their path. Likewise, placing a 2×2 square block of wood where you door closes will confirm that the operator’s safety reverse is properly set.

More About Garage Doors

Many garage doors open upward using an electric chain drive, which can often be remotely controlled from the resident’s vehicle with a small radio transmitter.[3] Garages are connected to the nearest road with a driveway. Interior space for one or two cars is typical, and garages built since the 1950s typically have a door directly connecting the garage to the interior of the house (an “attached garage”). Earlier garages were often detached and located in the back yard of the house, accessed either via a long driveway or from an alley.

In the past, garages were often separate buildings from the house (“detached garage”). On occasion, a garage would be built with an apartment above it, which could be rented out. As automobiles became more popular, the idea of attaching the garage directly to the home grew into a common practice. While a person with a separate garage must walk outdoors in every type of weather, a person with an attached garage has a much shorter walk inside a building.

Garages are often found where the attic entrance is located. Also used to store tools, bicycles and lawn equipment most garages have unfinished concrete floors. Some garages include a separate storage room to partially alleviate this problem.[4]

Around the start of the 21st century, companies began offering “portable garages” in the United States. Mostly, these garages are made of metal and do not attach to the house or other structure, much like the garages built prior to the 1960s. Many homeowner’s associations frown upon the installation of these nonconforming buildings, but still, their popularity is growing.

Garage flooring companies can install flooring products that are not generally available to the homeowner, providing a coating system that will last may years. These include epoxies, stained concrete and modular garage tiles (PVC vinyl, polypropylene or other polymers) to name a few.[5]

Garage Door Repair in Houston Texas

How to Choose a Garage Door Repair Company in Houston

In 2008, the Better Business Bureau of Texas developed its “Top
ten tips for choosing a garage door repair company.” The list was created in response
to a rash of complaints about repair companies that charged grossly excessive prices,
performed unneeded repairs, did shoddy work, and/or other questionable practices.
The list was good, but it badly needs updating for the Google era. If your area is
having a problem with unethical repair companies, here is our new and condensed list
that may be useful for sharing with customers or for posting on your website

1) Get bids from two or three companies.

You may be in a hurry to get your door fixed, but are you
prepared to pay $500 to $1,000 for a $150 repair? Getting
multiple bids is the best way to avoid getting scammed. In
most markets, a second bid alone will reveal a rip-off.
You can get these bids quickly over the phone. But when the
technician arrives, let him know that he must get your permission
before exceeding the bid. Don’t be afraid to reject any proposed
extra repairs.

2) Beware of the repair specialist.

Many unethical garage door companies intentionally target repair work because (1) customers are desperate for a quick fix and won’t get other bids, (2) customers don’t know the real cost of garage door parts, and (3) customers don’t know a necessary repair from a bogus one. If you get one bid from a company that focuses on repair, get another bid from a long-established company that does garage door sales and service.

3) Be wary of phones answered generically, such as “Garage doors” or “Door service.”

This tactic is used by slippery companies that operate under so many names that they can’t even answer their own phones honestly. If a company answers its phone strangely, ask them, “What company is this?” If they balk at this simple, honest question, hang up and call someone else.

C.M.G Garage Doors

C.M.G Garage Doors was created by a 3rd generation construction trained professional, who has many years of experience in the garage door industry. He is a family man who has a wife and three children, who also understands the value of saving money. We want to provide you affordable garage door service and quality work.

src: howtochooserepairco_spr2013.pdf